Memolub Multi-Point MPS-09 Lubricator | Power Lube Industrial

MEMOLUB® MPS-09
Multi-Point Lubricator

The MEMOLUB® MPS-09 (Multi-Point System) is a precise, reliable, and easy to install system that can lubricate 9 lube points with one lubricator.

  • Can be used with a MEMOLUB® HPS, EPS or PLCd
  • Available in 120cc, 240cc or 480cc reservoir
  • Dispenses 0.6cc from 3 outlet & 0.3cc from 6 outlets
  • Grease or Oil
  • Less costly than large centralized systems
  • Low maintenance

All of the materials required are available to quickly put your MEMOLUB® HPS lubricator to profitable use in a multi-point application.

Purchase prefilled nylon tubing and make installation as simple as "Plug 'n Lube"

How to order your Multi-Point System .pdf
How to order your Plug 'n Lube pre-filled nylon tubing .pdf

MEMOLUB Multi-Point Lubricator | Power Lube Industrial

The MPS-09 System consists of a MEMOLUB® high pressure lubricator, a distribution valve which meters the lubricant to all lube points, a mounting bracket and push-in tube fittings for your bearings.

All MEMOLUB® MPS systems have been primed before shipment and are ready for use. On first installation of the MPS system, all lube lines and bearings should be pre-charged with the same lubricant that was ordered with the MEMOLUB® lubricator (prefilled tubing is available and sold separately).

This system is especially suited for applications with several lube points in close proximity.

Grease or Oil:
There are two system types available; one for grease applications and one for oil applications. When ordering, be certain to specify the system appropriate for your application.

  • Grease up to an NLGI #2
  • Oil systems may require additional check valves

Memolub MPS Resouces:
Memolub Multi-Point System Distribution Block Set-up Guide .pdf
Memolub Multi-Point System Technical Data Sheet .pdf

Optional Parts:

Protective Cover: To protect your MEMOLUB® lubricator in harsher evironments we offer a nylon protective cover. This cover is sold seperately and is available for all three size lubricators.

Prefilled Nylon Tubing: Nylon tubing required to complete the installation is sold separately. The standard size tubing is 5/16” OD, but other sizes are available. Tubing can be purchased two ways; pre-filled in 5 foot increments from 5 to 30 feet, or empty in any length from 1 to 100 feet.

MEMOLUB Multi-Point Lubricator | Power Lube Industrial
  • Convert your MEMOLUB® lubricator to a MPS System
  • Many bearing adapters available

Contact us to learn more about the easy-to-use, effective GREASOMATIC lubricator.

  • Table based on the following:
  • - Tubing ID of 1/4" (6mm)
  • - Lube point threads no less than 1/8" NPT
  • - No inner pressure present in the component
  1. Lower temperatures can be achieved by using a low temperature grease and cold-weather battery packs
  2. Splitter Blocks cannot be used with oil, and are limited to 7 lubricant output settings.
  3. Maximum lube line length is dependent on ambient temperature, grease type and application back pressure.
Sorry, your query returned no results! The category you have chosen has no content at this time. Please try the "All Downloads" category.

Pages

Memolub
Application Case Study
Case Study No. 601
Industry:
Steel, Aluminum, Glass & Plastic
Application:
Steel Processing
Issue:
Six single-point lubricators could not generate enough pressure to overcome the back pressure from the machine. As a result, lubricant rarely reached the slides.
Solution:
The six lubricators were replaced with 1 MEMOLUB 6-point lubrication system, using the customer's existing lines. The 350psi output pressure was more than enough to reach the slides. The need to service only one lubricator, versus six, proved to be an added cost benefit.
Perma vs. Memolub | Power Lube IndustrialPerma vs. Memolub

Pages

Memolub
Application Case Study
Case Study No. 601
Application:
Steel Processing
Industry:
Steel, Aluminum, Glass & Plastic
Issue:
Six single-point lubricators could not generate enough pressure to overcome the back pressure from the machine. As a result, lubricant rarely reached the slides.
Solution:
The six lubricators were replaced with 1 MEMOLUB 6-point lubrication system, using the customer's existing lines. The 350psi output pressure was more than enough to reach the slides. The need to service only one lubricator, versus six, proved to be an added cost benefit.
Perma vs. Memolub | Power Lube IndustrialPerma vs. Memolub

Pages

Call to Order:
(800) 635-8170
Memolub
  MPS-09 Related Products
Product Description Item Number
L-Bracket Mount Kit IPMLLBK-1
  • L-Bracket Kit
  • Mount 2 Memolubs
IPMLLBK-2
Memolub Lubricant Refill Kits
See MEMOLUB Replacement Kits page
memolub dust cover IPM-DCSM-1
  • Memolub Standard and Mega Dust Cover
  • Fits Standard Model 120 and Mega Model 240
IPM-DCSM-1
Pre-filled Nylon Tubing
See Pre-filled Tubing Data Sheet